
A few days ago someone who had watched my video of the
rush hour in Assen asked me why there were so many similar looking bikes and so few had derailleur gears. This post is an attempt to explain.
This bike belongs to my wife, Judy. I am sure that some people looking at this picture will think it looks like an "old fashioned" bicycle. It's not. It's just a very practical bicycle. The result of many years of evolution of bicycle design for everyday use.
These bicycles are not an anachronism. They are an enabling technology for mass cycling. If you want the entire population to cycle, then this is the sort of bike they need to do it on. This bike has covered thousands of kilometres since we bought it (second hand), but apart from a little splashed mud it is spotless. It keeps itself clean and in good condition, despite no maintenance at all.
I'll explain some of the details of the design below.

The handlebars are relatively high and shaped like this because this leads to a very comfortable ride. This shape is also better suited than dropped or straight handlebars for attaching a
basket. Judy's baskets were made in 2004 for her previous bike but they are still good.

Chain case. This keeps your clothes clean, and makes it practical to ride in normal clothing. It also keeps the chain spotless, so that less maintenance is required. Chains last for many years when fully enclosed. Riders of bikes like this don't have to clean their chain after riding.
A full chain case like this is required to get these benefits. I have just a "hockey stick" shaped chain guard on my older
English 3 speed. This does not fully protect the chain so I have required a new chain this year and have also had to clean and re-lube the chain.

The front light and dynamo (generator). Having lights permanently attached to your bike in this way is far more convenient than having to remove them when you park the bike. Having a dynamo to run the lights means that they are always available.
Batteries go flat - especially if lights are left on. Removable lights can be removed by other people when you park your bike.

The rear wheel lock and the skirt guard.
The lock offers enough security for leaving your bike for a short period of time while shopping. The skirt guard keeps your clothes clean while you cycle, and make riding in normal clothing viable.
Note also the mudguards (fenders). These are steel and made to last, not the flimsy thermoplastic type which crack after a few years use.

This is the rear hub. This incorporates both the three gears on the bike and the rear brake, operated by a lever on the handlebars.
Enclosing the brake and gears leads to extremely high reliability. Neither the gears nor the brakes have required any maintenance, unlike my bike which has rim brakes and has required new brake pads.

Front wheel hub. The front brake is built into the wheel hub, and operated by the handle on the handlebars. This type of brake is extremely reliable. No adjustment has been required.
Some other features of the bike, all directed towards reliability and convenience, are:
- Sturdy steel luggage rack.
- Puncture proof tyres.
- Reflective sidewalls.
- Thicker spokes for stronger wheels.
- Chrome plated stainless steel rims - which look beautiful and never rust
- A paint finish designed to last 20 years of use outdoors.
This bicycle was made by
Azor in a factory just 40 km south of where we live. I took a video in the factory earlier this year, which features in a post about a visit to a
bike shop which I made earlier this year.
I also went out and took a few photos of other bikes parked around the city. You'll see that the majority incorporate the same features as seen above:

Two interesting bikes. The pink one is a child's bike made just as practical as an adults bike with all the features discussed above. This is needed as virtually all children use their bikes daily to
get to school. The other bike to its right has a low step over frame, which is useful for people with limited ability to lift their legs. e.g. older people, or people with disabilities.
The bike to the left of the child's bike has a fold down child seat on the back.

Two bikes fitted with front child seats and windscreens for the children. These are very common, as otherwise children sitting in front of their parents can get quite cold when being transported by bicycle in winter.
You can buy bicycles (moederfietsen) built specifically to carry two children, one in front and one behind. They come as standard fitted with both child seats and with a windshield like this.

One of the other ways that people use to carry small children is in bike trailers. This bike also has a seat mounted behind the handlebars, but no wind-shield.

This bike is fitted with a "springer" for
walking a dog while you cycle. Most people simply hold the dog's lead, which with a well trained dog works perfectly well. It is legal in this country to walk one dog while you cycle (but not two or more dogs).

An extra tall frame bike (the Dutch are now the tallest race in the world) and a bike with a serial number pressed into the frame in a very obvious way - an anti-theft idea that some manufacturers are using, and which makes it very difficult to disguise the serial number of a bicycle.

Bike fitted with a sturdy front rack. These are quite commonly used and work extremely well for carrying large and heavy items. Again an enabling technology to allow people to make journeys by bike for which they might otherwise have used a car. They fit most bikes and you can
buy them here.

A traditional looking bike, but actually new. This design is very popular, quite trendy, and many people like them.
As with many of the other bikes shown, this has just a back pedal (coaster) brake. It is legal to have just the back pedal brake here, and it's a common arrangement. Coaster brakes are very reliable, so again this is useful for an everyday bike.
Finally a view of people getting on with using their bikes, as they do everyday...
We use similar bikes for our cycling holiday customers.
27 reacties:
Nice to know Azor uses Basta sidewall generators for their bikes - ones without dynamo hubs anyway. Electra has just started using Basta generators for the Amsterdams, rather than the unlabeled extremely cheap one that came with mine, which A) wore out the rubber cap in about 3 months and B) I couldn't find replacement rubber caps for.
I saw a photo essay recently of an American tourist who went to Amsterdam and took a bunch of pictures of people on bikes. Someone who commented on his post said something like "I love all the after-market things they add to their bikes so they can ride in regular clothes." I thought that was pretty funny :)
Thanks for comprehensive blog about the bicycle - I just love your wife's bike, and it is my goal to have one ONE day. Thanks also, for your comment on our blogsite - handlebra easyrider club. Being new to it, it is very encouraging to hear from a pro in the slow cycling brigade. I'll get more movies up when I can of our short trips around Auckland. Might even go to Ellerslie and see what your old cycling route looked like.
Looks like common sense to me! Some of us are attempting to populate the US roads with similar bicycles.
Perhaps one day they will be a common site on US roads.
Aaron
I have been subscribed to this blog for over a week now and I honestly love this blog. While many of the previous posts are quite interesting, this post just took my breathe away.
I live in the Philippines, I'm 19 years old, I am an aspiring cyclist and it has been my dream to see my country or any other country become a cycling country. This blog-- the Netherlands just makes me want to dream even more.
There is something about seeing the anatomy of an "everyday bicycle" that makes my heart pump faster with awe and pump slower with -- I don't even have a word for it. This simple bicycle is a testament to the Netherlands as a cycling country. That simple bicycle is a vision of my dream that everyone can feel the freedom of cycling.
-------
Keep Up the Good Work!
I love it but I do wonder about the practicality of just three gears here in Scotland. I know Holland isn't completely flat, and you have to contend with headwinds, but I can't go anywhere from home without tackling several hills, and regularly use all 6 of my gears (and it's a low geared bike as it is). If I still lived in London, though, this would have been perfect.
Are there bikes like this, but with 6 gears? Presumably there are limits to what can be contained in a hub like that
@Melancholic: It is amusing that people often thing there are a lot of aftermarket parts on Dutch bikes. Generally there are none at all. These things come with the bikes.
@2wheels: I certainly hope for that. Of course they did used to be quite normal in the US too.
@jayjay: If you could make a video of the ride from Blanes Road in Weymouth all the way to James Cook High School in Manurewa then I could see my old school run which I've not done since I was 15 :-) (I really don't expect you to do this, but more pictures and videos of cycling in NZ are very welcome).
@Town mouse: There are now hubs with anything up to 14 gears in them. The Rohloff (14 gear hub) is very good quality but also extremely expensive. 8 and 7 speed hubs are relatively economical.
Typically, though, hub gears have a wider range than you might expect. The old traditional Sturmey Archer AW hub has three gears which range in ratio from 0.75 to 1.33. A span of 1.77 from the lowest to the top. A typical low cost derailleur setup has a 14-28 block which gives a total span of 2.0 (the number of gears changing only the number of steps in between).
Also note that the number of gears and the ratios only alter the difference between bottom and top. By choosing a different chainwheel at the front and/or a different sprocket at the back you can adjust the low gear to whatever you want it to be (any half decent bike shop can do this for you).
Many people have ridden over many hills with 3 speed bicycles, but there's more choice these days.
Also note that you can get very similar bikes with derailleurs if you wish. You lose the reliability to some extent, but can then have any gear ratios you desire.
Great post. Thanks for the inspiration!
We are starting to get bikes with all those accessories here in Australia too. I don't know how we ended up with such bare bones bikes here. Maybe because cycling became quite a specific, mostly sports market. When BMX became popular back when I was a kid we all started taking the chain and mud guards off our bikes to make them look more sporty... Maybe in doing so we laid the ground for a terrible 20 or was it 30 year trend.
Thanks for the info re hubs. 7 or 8 would do me fine, if I can track one down over here. Unfortunately we're in mountain biking territory here so it's hard enough finding a bike without suspension, let alone a fully loaded dutch-style bike
I think you go back and forth to London, don't you ? If so, drop in on velorution who sell sensible bikes in the Capital, including Azor like the bike in the article, and who also have a very interesting blog.
Dear Town Mouse,
They actually do make real bikes in the UK. I know for sure, because I just bought one, the Pashley Sovereign Roadster.
Its Sturmy Archer five-speed internal hub gearing has a 225% gear range. That should be enough for even the steepest hills here, particularly with the electric assist that I'm having put on it.
It may not even be necessary for you to come here to Toronto to buy a British bike. There's a photo and description of it here:
http://store.curbside.on.ca/index.php?main_page=product_info&cPath=4_109_114&products_id=131
Shame that such eminently sensible bikes are so uncommon in London. Virtually every bike you see at the lights has either 27 gears or just one, when 3-5 is surely the right sort of number in such a non-alpine city.
(BTW David, I've added you to the list of blogs on my blog.)
yup - I've got my eye on a Pashley - it's good to know about the gear range. I think I can get one without trugging down to the smoke as well. I did go to Velorution once and found them a little bit intimidating - the bikes they showed me were beautiful but a bit stately and a bit too beautiful, if that makes any sense. I don't want to have to live up to my bike! I just want something to ride on...
I really should have mentioned Pashley. They are an excellent company who along with Brompton are one of only two mass manufacturers of bikes still in the UK (there are several excellent specialist manufacturers too, and this is not "damning by faint praise").
I own a Pashley myself, though a rather different one.
Hi David!
Can you give any prices in euros for this kind of bikes? Also for the children seats etc
@melancolic optimist
Velo Orange carries the caps you want, but only in black at the moment.
@town mouse
Raleigh and many other manufacturers used 3 speed hubs for many, many years in the UK. At one time the UK made more cycles than all of the others combined. I use a lovely old British built 3 speed and with a larger cog in the rear it handles 95% of the riding I do, the other 5% I walk up the hills. LOL
Aaron
@Einar: This is the website of the closest bike shop to our home. Click on Assortiment and you'll see the bikes available. "Stads fietsen" are town bikes, "Moeder fietsen" are the ones which come with child seats etc.
I'm going to do a future blog post on the difference between a moeder fiets and a stadfiets with child seats bolted on. There are a lot of special features on the bikes which are designed for carrying children.
Good quality baskets come from here, of course :-)
@2whls3spds: My town bike is also an old English 3 speed. Very fine machines. I enjoy riding mine a lot.
For practicality the old bikes do suffer a bit in comparison with the Dutch designs. All the details: brakes, gears, skirtguards, chainguards, lights, really strong rack, robust paint etc. which are better on bikes like my wife's.
You won't get any argument from me on the quality and the advances of the newer bikes, especially ones like the Azor's or Gazelles.
People sometimes forget that the old Raleighs (and other all steel British marques) are indicative of technology that is nearly 100 years old! But it is a technology that remains usable even to this day.
I really do appreciate my AXA Defender wheel lock and chain, my B&M Lumotec IQ Fly Senso headlight, along with the roller brakes...modern stuff at it's finest. ;-)
Aaron
When I moved here, my Cloggie fiance was convinced I would barely use my bike and we opted to get one of the cheapest ones we could find at Halfords. I ride it very often and now that I am getting faster and a bit more fit I am now aiming to cycle to the station each morning on my way to work. I really wish I had bought a better bike now. A lot of people I know here have second hand bikes and have had them for quite a number of years but still look a lot more sturdy and reliable than mine.
Cool to see an older Azor. I've had mine for about 4 months and it was very difficult for me to track one down in the States. I love her baskets!
Thanks for this extensive article. I can't help but laugh at audacity of the Dutch. They'll put anything on a bike, as long as it's something they need. It shows what innovation happens in cycling, when cars aren't the ideal. Thanks for raising the bar.
Here, here! Great post. I love this style of bike. It is gaining popularity again after more than a decade of the mountain bike being used for city travel (I admit, I had a Mtn Bike for college life when one of these "reliable" bikes would have been better). I have a bakfiets now and have not looked back. Great blog post, great blog. I found your blog through a Clever Cycles tweet.
Doesn't the sidewall generator (a) wear down the tire and (b) create a lot of drag, slowing the rider down?
Also, while a singlespeed or three speeds may be OK for a flat-as-a-pancake country like the Netherlands, some of us live in hilly or even mountainous regions.
Anonymous:
No, the "sidewall generator" doesn't wear down the tyre. I wouldn't run one on a skinwall tyre, but there are plenty of tyres available with a special track for it to run on.
Also, it creates very little drag, perhaps around 5% of your energy goes into this, reducing your speed by much less than 5% (aerodynamic effects dominate and are a cube law).
If you have hills, buy a bike with a more gears. Identical bikes are available with 8 gear hubs. As I explained in a previous reply, it isn't actually the number of gears that matters so much as how far apart they are.
However, it isn't actually the problem you think it is. I used to live in the UK and quite often rode my 3 speed bike over hills there, sometimes 10% or more, with no problems.
If you went back to 1950 or so, you'd find many people in the UK were quite capable of doing the same thing, on the bikes which are the spiritual ancestors of this one.
Interesting with dynamo. Here in Denmark, everyone but everyone is now using Reelights: http://www.reelight.com/Default.aspx?ID=56 - a magnet attached to the spokes, the light itself bolted to the axle, all done in 5 minutes and voila you have permanently on, no drag, no batteries lights.
Great invention!
Neil
Neil: These types of lights are available here too. Both the originals and identical looking but cheaper chain store branded copies. They don't seem very popular at all.
They've been tested by magazines and generally found to be lacking in both robustness and brightness. They also have the problem that being attached to the rear axle means that they disappear underneath panniers so they're not great on practical bikes.
As for "no drag". It's true that they have little drag, but they do cause some drag. There is no "free lunch". The energy to run the light comes from your pedalling.
The Dutch cycling market is not fickle and not swayed too much by fashion. The Dutch cycle more than people from any other country and they know about bikes. Those things that work best get used most.
According to the Wikipidia article on bicycle gearing systems, hub gears are less efficient than derailleurs; they're also heavier. Is this not true?
Anonymous: It's true, but it's a simplification. We're talking about utility bikes here, used everyday, and perhaps kept outdoors. I'd not choose a hub gear for a racing bike, but I have one on my town bike.
A well maintained derailleur gear system is very efficient. However, it is very difficult to fully enclose the chain with a derailleur. So difficult that no production bikes do this. As a result, these bikes quickly become less efficient as the chain gets dirty and rusty. A hub gear with a full chain case is then much more efficient.
Also, some hub gears are actually extremely efficient. The Rohloff hub is generally considered similar in efficiency to a derailleur, and the latest Shimano Alfine is very good too.
Post a Comment